If you’re using ethernet cable, you might have to crimp your own connectors on if they’re not already installed. Next unwrap and remove the fish tape, and your cable will be ready to hook up to your camera when you’re ready to install it. RELATED: How to Crimp Your Own Custom Ethernet Cables of Any Length This job is a whole lot easier with a friend helping you. Once the fish tape extends far enough into the attic for easier access, tape the end of the cable to the fish tape and pull on the fish tape from the outside to thread the cable through the hole you drilled. You can feed the fish tape up into the hole that you just drilled for your camera. There’s no way I’m crawling all the way to the edge here, so I have fish tape do that for me. So to solve that, fish tape will be your best friend. This is a lot easier to do if you have steel fish tape-it’s very difficult to physically locate yourself around the edge of your attic, since that’s where your roof slopes down and creates a very cramped space to work in. So to start, I’m going to take cable and feed various lengths out to the edges where my cameras will be. This is also where the order of things might be different for you based on your situation, but essentially you’ll be drilling holes either through walls or ceilings in order to feed cables to where you need them to go.įor my installation, all of the cameras’ cables will converge in the attic above my garage, and from there they’ll all feed up into the main attic above the second floor. Once you have holes drilled for your cameras, it’s time to run cable to each of your camera locations. Step Three: Run Cables to Each Camera Location Usually you have to use a spade bit for the bigger hole, but you might be able to find a regular drill bit that’s big enough. Then drill the bigger hole in the center that the cable will feed through. Get your power drill and a drill bit and drill pilot holes where the mounting screws will go. If yours doesn’t come with these, hold the camera up to the wall or ceiling where you want it and mark the holes with a pencil. Some kits will come with a template sticker that makes the job a lot easier. In any case, start by marking a hole where the camera’s cable will feed through, as well as holes for where the camera’s mounting screws will go. However, if you have to drill through brick or other masonry, you’ll likely want a hammer drill with some masonry drill bits. For instance, I’m just drilling through wood, drywall, and aluminum, so a regular power drill and some basic drill bits will work fine. Step Two: Prepare the Camera Installationĭepending on where exactly you install your cameras, you may need some different tools than what I use. Obviously, you’ll have the best judgement on this, but it’s something you’ll need to keep in mind. From there you can run the cable through the porch’s own little attic and then up into the main attic, taking it wherever you want from there. So instead of mounting it on an outside wall, perhaps mount it on your front porch’s ceiling. That is your limiting factor when it comes to installing the cameras. You have to think about what makes the most sense as far as ease of installation (and if it’s even possible to install a camera where you want it).įor example, it would be great to have a camera mounted on the outside wall next to your front door in the upper corner, but you have to think about how you’re going to route the cable from the camera all the way to the DVR box. When it comes to installing wired security cameras, it’s not enough to pick just any spot and mount them. Step One: Figure Out Where You Want Your Cameras With my house, the best place to mount my cameras is on the soffit (the area underneath the roof overhang), that way the cables can travel directly through the attic. Most systems will also come with a mouse, but a keyboard is also recommended. Since the cameras directly plug into the DVR box, this means that if you install a camera by your back patio and the DVR box is upstairs in your home office, you’ll need to route the camera’s cable through your house in order to connect it to the DVR box, which can get a bit complicated, depending on how your house is built how exactly you plan to route the cable.įrom there, the DVR box gets plugged into a power outlet and then you connect an external monitor to the DVR box to manage the entire system, see a live view of all the cameras, and review past recordings.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |